Skip to main content
Log in
Siemens 6AG1132-6BD20-7CA0 — PLCs (Programmable Logic Controllers)

Siemens 6AG1132-6BD20-7CA0 4-DO Transistor Module, 2 A, ET 2

MPN6AG1132-6BD20-7CA0

Siemens SIPLUS, ET 200SP digital output module, 6AG1132-6BD20-7CA0, 4 transistor outputs at 24 VDC / 2 A, width 15 mm.

Siemens 6AG1132-6BD20-7CA0 datasheet (PDF)
Source DocumentedChannel stated on listing & quote
Condition PhotosReal unit photos / video on request
WhatsApp AnswersFast human replies for machine-down parts
Worldwide DispatchDHL/FedEx — transit quoted per order
Independent China distributor & sourcing agent· Listing updated Sep 2026

Specifications

6AG1132-6BD20-7CA0 — I/O
ParameterValue
Digital outputs4
6AG1132-6BD20-7CA0 — Electrical
ParameterValue
Rated value (DC)24 V
Permissible range, lower limit (DC)19.2 V
Permissible range, upper limit (DC)28.8 V
Power loss (typ.)1 W
Short-circuit protectionYes
6AG1132-6BD20-7CA0 — Environmental
ParameterValue
Installation altitude, max.5 000 m
Operating temperature, min. (horizontal mounting)-40 °C; = Tmin (incl. condensation/frost)
Operating temperature, max. (horizontal mounting)70 °C; = Tmax; see Derating BasedOn (e.g. manual), additionally Tmax > 60 °C max. total current 1 A
Ambient temperature vs. altitude/pressure deratingTmin ... Tmax at 1 140 hPa ... 795 hPa (-1 000 m ... +2 000 m) // Tmin ... (Tmax - 10 K) at 795 hPa ... 658 hPa (+2 000 m ... +3 500 m) // Tmin ... (Tmax -20 K) at 658 hPa ... 540 hPa (+3 500 m ... +5 000 m)
6AG1132-6BD20-7CA0 — Mechanical
ParameterValue
Width15 mm
Height73 mm
Depth58 mm
Weight (approx.)30 g

Product details

4-channel transistor output slice for ET 200SP

The 6AG1132-6BD20-7CA0: The module supports isochronous mode with a jitter of 8 µs and a minimum bus cycle time of 500 µs, making it suitable for high-speed sequencing or coordinated motion handshakes.

Panel fit and thermal limits

At 15 mm wide, 73 mm tall, and 58 mm deep, the module occupies a single slot on the DIN rail. It mounts on BU type A0 base units (common for ET 200SP output slices). Below 60 °C each output can carry its full 2 A rating without restriction.

Diagnostics and serviceability

Every channel has independent short-circuit and wire-break detection with a red LED indicator; a green LED per channel shows signal state. The module also reports group errors and diagnostic alarms via the backplane. Firmware is field-updatable (version V1.0 shipped) and substitute values can be assigned per channel for failsafe behavior. The module draws 60 mA from the 24 V backplane (no load) and dissipates 1 W typical.

Frequently asked questions

What is the derating requirement above 60 °C ambient?

When mounted horizontally in ambient temperature above 60 °C and up to 70 °C, the total output current across all four channels must be limited to 1 A. Below 60 °C, each channel can deliver its full 2 A rating.

What backplane base unit does this module require?

It uses BU type A0 base units per the SIPLUS ET 200SP system specifications.

MPN
6AG1132-6BD20-7CA0