Skip to main content
Log in
Siemens 6ES7131-6CF00-0AU0 — Digital Input Modules

Siemens 6ES7131-6CF00-0AU0 DI Module, 8 Inputs, 1 A at 60°C

MPN6ES7131-6CF00-0AU0
Active

Siemens SIMATIC ET 200SP digital input module, 8 inputs, 1 A at 60 °C, 20 mm wide, BU type U0.

$54.61 – $156.09Ref. price · indicative, final on quote
Siemens 6ES7131-6CF00-0AU0 datasheet (PDF)
Source DocumentedChannel stated on listing & quote
Condition PhotosReal unit photos / video on request
WhatsApp AnswersFast human replies for machine-down parts
Worldwide DispatchDHL/FedEx — transit quoted per order
Independent China distributor & sourcing agent· Listing updated Sep 2026

Specifications

6ES7131-6CF00-0AU0 — Inputs
ParameterValue
Number of digital inputs8
Max. inputs, up to 60 °C1 A
2-wire sensor supportYes
6ES7131-6CF00-0AU0 — Electrical
ParameterValue
Rated value (DC)48 V
Input voltage at signal "1"AC > 14 V, DC > 34 V
Input voltage at signal "0"AC/DC < 10 V
Permissible range, lower limit (DC)40.8 V
Permissible range, upper limit (DC)57.6 V
Input current at signal "1" (typ.)3.5 mA
Power loss (typ.)1.5 W
Cable length, unshielded, max.600 m
Cable length, shielded, max.1 000 m
6ES7131-6CF00-0AU0 — Timing
ParameterValue
Input delay 0 to 1, max.15 ms
Input delay 1 to 0, max.20 ms
Input delay, parameterizable valuesNo
6ES7131-6CF00-0AU0 — Environmental
ParameterValue
Max. ambient temperature, horizontal installation60 °C
6ES7131-6CF00-0AU0 — Diagnostics & Isolation
ParameterValue
Short-circuit protectionYes; Per module, 5x 20 mm fuse, 2 A/250 V, quick-response, replaceable
Diagnostics functionYes
Diagnostic alarmYes
Isolation between channelsNo
Isolation between channels and backplane busYes
Isolation test voltage1 200 V DC between supply voltage and backplane bus
6ES7131-6CF00-0AU0 — Mechanical
ParameterValue
Depth58 mm
Height73 mm
Width20 mm
6ES7131-6CF00-0AU0 — Specifications
ParameterValue
Rated value (AC)48 V; 24 V/48 V; 50 Hz/60 Hz
Address space per module, max.1 byte

Product details

The Siemens 6ES7131-6CF00-0AU0 is an 8-channel digital input module for the ET 200SP distributed I/O system. It accepts 2-wire sensors and reads P-switching inputs, with a rated supply of 48 V AC/DC (24 V/48 V AC at 50/60 Hz also supported). Each channel can sink up to 1 A continuously at 60 °C, making it suitable for driving small solenoids or indicator loads directly without an external relay.

The module is 20 mm wide and 73 mm tall, fitting the ET 200SP base unit type U0. It requires a potential distributor module for 3-wire or 4-wire sensor connections. Unshielded cable runs up to 600 m are allowed; shielded runs extend to 1 000 m. The isolation is tested at 1 200 V DC between the supply voltage and the backplane bus.

Electrical Characteristics

Signal thresholds: a logic '0' is detected for AC/DC below 10 V; logic '1' requires AC above 14 V or DC above 34 V. Typical input current at signal '1' is 3.5 mA. Switching delays are 15 ms max for 0→1 and 20 ms max for 1→0. The module draws 1.5 W typical from the backplane. Diagnostic alarms and group error reporting are supported; firmware version is V0.0 and is not field-upgradable.

Frequently asked questions

What are the key ratings for this module?

It has 8 digital inputs, each rated for 1 A at 60 °C, with a rated supply of 48 V AC/DC. The module is 20 mm wide and supports diagnostic alarms.

Can this module replace a 6ES7522-5HF00-0AB0 without rewiring?

No. The 6ES7131-6CF00-0AU0 is an ET 200SP digital input module, while the 6ES7522-5HF00-0AB0 is a S7-1500 digital output module. They serve different functions and use different backplane connectors, so a direct swap is not possible without rewiring and a different base unit.

MPN
6ES7131-6CF00-0AU0