Skip to main content
Log in
Siemens 6ES7132-6BD20-0DA0 — Digital Output Modules

Siemens 6ES7132-6BD20-0DA0 ET 200SP DQ, 4ch, 24V, 2A, PWM

MPN6ES7132-6BD20-0DA0
Active

Siemens 6ES7132-6BD20-0DA0 ET 200SP digital output module, 4 push-pull outputs, 24 V DC, 2 A, PWM and oversampling support.

$121.92 – $352.80Ref. price · indicative, final on quote
Siemens 6ES7132-6BD20-0DA0 datasheet (PDF)
Sourced new & surplus through independent channelsAuthenticity-screened · ESD-safe packingListing updated Aug 2026

Specifications

6ES7132-6BD20-0DA0 — Outputs
ParameterValue
Digital outputs4
Output typeSource output (PNP, current-sourcing)
6ES7132-6BD20-0DA0 — Electrical
ParameterValue
Rated value (DC)24 V
Output current, resistive load, max.5 kHz
Output current at signal "1" (rated)2 A
Total output current per module, max.8 A
Permissible range, upper limit (DC)28.8 V
Permissible range, lower limit (DC)19.2 V
Residual current at signal "0", max.0.1 mA
Output current up to 60 °C, max.2.5 A; DQ mode
Power dissipation (typ.)2.5 W; at 24 V, 25 °C, DQ mode, 2 A per channel
Inductive shutdown voltage clampM (-1 V)
Load resistance, upper limit3 400 Ω
Load resistance, lower limit12 Ω
Isolation between channelsNo
Isolation between channels and backplane busYes
Isolation test voltage707 V DC (type test)
6ES7132-6BD20-0DA0 — Protection & Diagnostics
ParameterValue
Short-circuit protectionYes
Reverse polarity protectionYes
Diagnostics functionYes
Diagnostic alarmYes
Short-circuit response threshold (typ.)6 A
Short-circuit detectionYes; Module-wise
Wire-break detectionNo
Output can drive a digital inputNo
6ES7132-6BD20-0DA0 — Performance
ParameterValue
Output switching delay 0 to 1, max.1 µs
Output switching delay 1 to 0, max.1 µs
Switching frequency, inductive load, max.5 kHz
Switching frequency, lamp load, max.5 kHz
6ES7132-6BD20-0DA0 — Environmental
ParameterValue
Operating temperature, horizontal mount, max.60 °C
Operating temperature, horizontal mount, min.-30 °C
6ES7132-6BD20-0DA0 — Mechanical & Connection
ParameterValue
Cable length, unshielded, max.50 m
Cable length, shielded, max.50 m
Width15 mm
Height73 mm
Depth58 mm
Weight (approx.)31 g

Product details

The 6ES7132-6BD20-0DA0 is a 4-channel digital output module for the ET 200SP system, with push-pull outputs rated at 2 A per channel at 24 V DC. It supports PWM and oversampling operating modes, with isochronous mode available in DQ and OVS modes, and a maximum jitter of 1 µs. Transition times are also 1 µs. Diagnostic alarm and group error are provided, with module-wide short-circuit detection. Hysteresis and I&M data 0 to 3 are supported. The module is 15 mm wide and fits base unit type A0. Typical power loss is 2.5 W at full load (24 V, 25 °C, DQ mode, 2 A per channel).

MPN
6ES7132-6BD20-0DA0