Skip to main content
Log in
Siemens 6ES7132-6FD00-0CU0 — Digital Output Modules

Siemens 6ES7132-6FD00-0CU0 ET 200SP DQ Module, 20mm, 24-230V

MPN6ES7132-6FD00-0CU0
Active

Siemens ET 200SP, 6ES7132-6FD00-0CU0, digital output module, DQ, current-sourcing, 8 outputs, 20 mm width, BU type U0, rated 230V AC, 8 A max.

$149.86 – $443.85Ref. price · indicative, final on quote
Siemens 6ES7132-6FD00-0CU0 datasheet (PDF)
Sourced new & surplus through independent channelsAuthenticity-screened · ESD-safe packingListing updated Aug 2026

Specifications

6ES7132-6FD00-0CU0 — Outputs
ParameterValue
Digital outputs4
Output typeTriac
6ES7132-6FD00-0CU0 — Electrical
ParameterValue
Output current, resistive load, max.10 Hz; Applies to DQ mode; limited by line frequency in PC mode
Output current at signal "1" (rated)2 A
Output current, max. per circuit / per module4 A; note derating data in the manual
Total output current per module, max.8 A
Output voltage at signal "1" (min.)20.4 V
Residual current at signal "0", max.3 mA
Output current up to 60 °C, max.4 A
Power dissipation (typ.)9 W; Active power, load voltage 230 V, all outputs loaded with 2 A, 50 Hz
Isolation between channelsNo
Isolation between channels and backplane busYes
Isolation test voltage2 545 V DC/2 s (routine test)
6ES7132-6FD00-0CU0 — Protection & Diagnostics
ParameterValue
Short-circuit protectionNo; external fusing necessary
Diagnostics functionYes
Diagnostic alarmYes
Short-circuit response threshold (typ.)1 mA; 40 V AC or more
Short-circuit detectionNo
Wire-break detectionYes; channel by channel
Redundant load controlYes
Output can drive a digital inputYes
6ES7132-6FD00-0CU0 — Performance
ParameterValue
Output switching delay 0 to 1, max.40 ms; 2 AC cycles
Output switching delay 1 to 0, max.20 ms; 1 AC cycle
Switching frequency, inductive load, max.2 A
Switching frequency, lamp load, max.1 Hz; Applies to DQ mode; limited by line frequency in PC mode
6ES7132-6FD00-0CU0 — Environmental
ParameterValue
Operating temperature, horizontal mount, max.60 °C
Operating temperature, horizontal mount, min.-30 °C
6ES7132-6FD00-0CU0 — Mechanical & Connection
ParameterValue
Cable length, unshielded, max.600 m
Cable length, shielded, max.1 000 m
Width20 mm
Height73 mm
Depth58 mm
Weight (approx.)50 g

Product details

The Siemens 6ES7132-6FD00-0CU0 is a current-production ET 200SP digital output module. It delivers 8 current-sourcing outputs (DQ) rated for 24 V AC to 230 V AC, each switched via phase control with a control range of 8.5% to 100% of the phase angle. The module is 20 mm wide and mounts on a BU type U0 base unit, which handles the 1-wire, 2-wire, or 3-wire connection scheme depending on the potential distributor.

Derating and thermal limits

Output current is temperature-dependent: 8 A per channel up to 30 °C, 6 A up to 40 °C, and 4 A up to 50 °C. For a 50 °C panel, figure 4 A maximum per output — no headroom for parallel tie unless you respect the package dissipation of 9 W typ at full load on 230 V AC. Unshielded cable runs up to 600 m; shielded max 1 000 m. Wire-break detection and diagnostic alarm are built in.

Sourcing and compatibility

For a BOM freeze, this is a stable line. No PCN or LTB activity. Firmware updates are supported, and the module carries I&M data 0 through 3 for asset tracking.

Frequently asked questions

What does DQ = Yes mean for this module?

DQ (digital output) rated Yes means it switches AC loads up to 230 V AC via phase control, current-sourcing topology.

Will this module fit into a panel originally wired for a 6ES7522-5HH00-0AB0?

No. The 6ES7132-6FD00-0CU0 uses the ET 200SP BU type U0 base unit, while the 6ES7522 uses the S7-1500 form factor with a different base bus. Physical and electrical interfaces are incompatible.

Does the module support phase control and diagnostics?

Yes. Phase control covers 8.5% to 100% of the phase angle. Diagnostic alarm and wire-break detection per channel are built in.

MPN
6ES7132-6FD00-0CU0