ABB 3AXD50000161874 Drive Module, 0.75 kW, 4.8 A, R1 Frame

Specifications

Electrical Output

3AXD50000161874 — Electrical Output
Parameter	Value
Output power, normal duty (Pn)	0.75 kW
Output current, normal duty (In)	4.8 A
Output power, heavy duty (PhD)	0.55 kW
Output current, heavy duty (IhD)	3.7 A
Output power, light-overload duty (PlD)	0.75 kW
Output current, light-overload duty (IlD)	4.6 A
Output power, heavy duty (UL, Hp)	0.75 Hp
Output current, heavy duty (UL)	3.2 A
Apparent power output	1.9 kV·A
Output power, light-overload duty (UL, Hp)	1 Hp
Efficiency class (IE)	IE2
Output current, light-overload duty (UL)	4.6 A
Standby loss	14 W
Power consumption	72 W

Electrical Input

3AXD50000161874 — Electrical Input
Parameter	Value
Input voltage range	200 ... 240 V
Number of phases	3-phase
Frequency	47.5 ... 63 Hz
Power factor	0.98

Control & I/O

3AXD50000161874 — Control & I/O
Parameter	Value
Digital inputs / outputs	5 / 2
Communication protocol	MODBUS
Analog inputs	2
Analog outputs	1
Hardware interfaces	Industrial Ethernet 0

Environmental

3AXD50000161874 — Environmental
Parameter	Value
Temperature rating, max.	Maximum 50 °C
Operating humidity	5 ... 95
Altitude	1000 m
Noise level	63.10 dB(A)

Mechanical

3AXD50000161874 — Mechanical
Parameter	Value
Degree of protection (IP)	IP20
Enclosure type (NEMA)	Open Type
Frame size	R1
Mounting type	Module

Approvals

3AXD50000161874 — Approvals
Parameter	Value
RoHS compliance	Following EU Directive 2011/65/EU and Amendment 2015/863 July 22, 2019
REACH compliance	True - contains substances > 0.1 mass percentage

Product details

What this module is and what it delivers

The ABB 3AXD50000161874 is a current-lifecycle drive module in the R1 frame size, rated for 0.75 kW normal-use output at 4.8 A on a 200–240 V three-phase supply. It includes the control unit, so the order code covers the drive itself — no separate controller board to source. Heavy-duty use drops to 0.55 kW / 3.7 A; light-overload use holds at 0.75 kW / 4.6 A. Under UL listing the heavy-duty output is 0.75 Hp / 3.2 A, light-overload 1 Hp / 4.6 A. The IE2 efficiency level and 0.98 power factor keep line draw clean for a 0.75 kW machine. Standby loss is 14 W, so the module idles without pulling much heat into the panel. Sound level is 63.10 dB(A) — noticeable in a quiet room but unremarkable on a factory floor.

I/O and communication — what you get on the terminal strip

Two analog inputs and one analog output are available for speed reference or process feedback. Five digital inputs and two digital outputs handle start/stop, fault reset, and status. No industrial Ethernet interface is present — the onboard communication is MODBUS only, so if the line uses PROFINET or EtherNet/IP, a separate gateway or option module is needed. The module mounts as a standalone unit (IP20, Open Type NEMA enclosure) and is sized for a 1000 m altitude without derating. Operating temperature maxes at 50 °C; humidity range is 5 to 95% non-condensing.

Compliance and sourcing posture

WEEE category 5 (Small Equipment, external dimension ≤ 50 cm) applies for end-of-life take-back. No battery is included, so no additional hazardous-waste classification for the drive itself.

The R1 frame is the smallest in this drive family. The next size up (R2) handles higher normal-use output on the same voltage class, but the R1 keeps the panel footprint tight for a 0.75 kW motor.

Frequently asked questions

What is the SCIP number for this drive module?

The SCIP number is 483516f7-5042-4d76-a918-d7fab20a54ce Finland.

What compliance documentation is available for the 3AXD50000161874?

RoHS compliance follows EU Directive 2011/65/EU and Amendment 2015/863 (RoHS date 20230303). REACH declaration confirms substances above 0.1% mass percentage (REACH date 20250905). UL listing covers heavy-duty use at 0.75 Hp / 3.2 A and light-overload at 1 Hp / 4.6 A.