Skip to main content
Siemens 3RW5524-1HA14

Siemens 3RW5524-1HA14 Soft Starter, 200-480V, ATEX, Fieldbus

MPN 3RW5524-1HA14
Active

Siemens SIRIUS 3RW5524-1HA14 soft starter, 200-480 V rated voltage, ATEX / IECEx certified, trip classes 10A/10E/20E/30E, PROFIBUS/Modbus/EtherNet/IP, screw terminals.

$1,159.00 Ref. price · indicative, final on quote
Dispatch SLA24-48h Global Rush
Quality CheckOriginal Seal & Physical QC
IncotermsDAP / DDP Available
Source DocumentedChannel stated on listing & quote
Condition PhotosReal unit photos / video on request
WhatsApp AnswersFast human replies for machine-down parts
Worldwide DispatchDHL/FedEx — transit quoted per order
Independent China distributor & stockist· Listing updated Sep 2026

Specifications

3RW5524-1HA14 specifications
ParameterValue
Mountingscrew fixing
Depth203 mm
Width185 mm
Height306 mm
Trip classCLASS 10 A / 10E (default) / 20E / 30E; acc. to IEC 60947-4-2
Service factor1.15
Digital output version3 normally-open contacts (NO) / 1 changeover contact (CO)

Product details

The Siemens 3RW5524-1HA14 is a SIRIUS soft starter for three-phase induction motors, rated for a supply voltage of 200 to 480 V. It carries ATEX and IECEx certification for use in potentially explosive atmospheres — that means the soft starter itself is approved for installation in Zone 2 or Zone 22 areas (equipment protection level Gc/Dc), so you can place it inside the hazardous boundary rather than forcing a remote panel. Trip class is configurable: CLASS 10A or 10E by default, with options for 20E or 30E per IEC 60947-4-2. The 10A setting clears a stall in 10 seconds at 7.2x rated current — standard for most conveyor and pump starts. Bumping to 30E gives you 30 seconds for high-inertia loads like centrifuges or large fans without nuisance tripping. Communication is multi-protocol out of the box: PROFIBUS, Modbus RTU, Modbus TCP, and EtherNet/IP are all listed. That saves a separate gateway card for plants running mixed-fieldbus lines. PROFIenergy is also supported when paired with the PROFINET High-Feature module, letting the drive coordinate energy-saving pauses during idle periods.

Panel fit and clearance

Dimensions: 306 mm high, 185 mm wide, 203 mm deep. Mounting is via screw terminals. Clearance requirements are asymmetrical — 100 mm above, 75 mm below, only 10 mm forward, 0 mm backward, and 5 mm to the side. That tight rear clearance means you can back it against a panel wall, but the 100 mm top gap is mandatory for heat plume rise; skimping there derates the unit.

Lifecycle and compliance posture

Compliance documentation is comprehensive: CE marking for European markets, UL and CSA approvals for North America, plus ATEX and IECEx for hazardous locations. Accuracy Class 5 per IEC 61557-12 applies to the integrated metering function — that means current and voltage measurement uncertainty stays within 5 % of reading, adequate for energy monitoring but not revenue-grade billing.

What the control features mean on the line

Built-in torque control, voltage ramp, pump ramp down, and breakaway pulse cover the common starting profiles. Voltage ramp is the standard for reducing inrush on conveyors; pump ramp down closes valves gradually to avoid water hammer. Breakaway pulse delivers a short high-torque burst to break a stuck load loose before ramping — useful for crushers or screw feeders that bind after a shutdown. Analog output is configurable as 4-20 mA or 0-10 V, defaulting to 4-20 mA. That lets you feed motor current, power, or temperature to a PLC analog card without a separate transducer. The error logbook, event list, trace function, and motor heating model are all on-board — no extra software license for basic fault analysis. Service factor of 1.15 means the soft starter can handle a motor nameplated at 115 % of its rated load without tripping — common in pump applications where the motor is oversized for the driven load. DC braking is included for quick stops on low-inertia loads, though it should not be used for frequent jogging as it heats the rotor.

MPN
3RW5524-1HA14