Skip to main content
ABB 266DSHHSMA1B1L1C1H4

ABB 266DSHHSMA1B1L1C1H4 DP transmitter, 160 kPa

MPN 266DSHHSMA1B1L1C1H4

ABB 266DSH Differential Pressure Transmitter, 266DSHHSMA1B1L1C1H4, HART and 4 to 20 mA output, 1.6 to 160 kPa span, Monel diaphragm, 1/4 in. NPT-f process connection, integral LCD.

$1,881.00 Ref. price · indicative, final on quote
Dispatch SLA24-48h Global Rush
Quality CheckOriginal Seal & Physical QC
IncotermsDAP / DDP Available
Source DocumentedChannel stated on listing & quote
Condition PhotosReal unit photos / video on request
WhatsApp AnswersFast human replies for machine-down parts
Worldwide DispatchDHL/FedEx — transit quoted per order
Independent China distributor & stockist· Listing updated Sep 2026

Specifications

266DSHHSMA1B1L1C1H4 specifications
ParameterValue
Product type266DSH Differential Pressure Transmitter
ApplicationDifferential measurement at standard static pressure

Product details

What the order code actually configures

The ABB 266DSHHSMA1B1L1C1H4 is the 266DSH Differential Pressure Transmitter ordered for differential measurement at standard static pressure (S), paired with HART and 4 to 20 mA output on the advanced-functionality firmware — the protocol stack that drops straight into a DCS or asset-management host without a separate gateway. Sensor span runs from 1.6 to 160 kPa (16 to 1600 mbar, 6.4 to 642 inH2O), which puts this build in the low-to-mid DP range — the workhorse span for filter ΔP, vessel level via DP on a wet leg, and small-bore flow-element differentials rather than very high static line pressures.

Diaphragm, fill fluid, and process side

The wetted diaphragm is Monel 400 with silicone-oil fill, listed NACE — a corrosion-resistant build for hydrocarbon, offshore, and mildly sour-service lines where 316L is marginal, and the silicone fill keeps the span stable across the typical process-temperature swing. Process flanges and adapters are AISI 316L stainless with a horizontal 1/4 in. – 18 NPT-f direct connection, and the bolt/gasket set is 316 ss with Viton — the standard static-pressure configuration for a horizontal impulse line on a separator or filter housing.

Housing, display, and field-side hardware

The housing is the aluminium-alloy barrel with an M20 x 1.5 (CM 20) conduit entry — the variant specified for WirelessHART installations where the barrel form factor routes cleanly into a pole- or pipe-mount antenna bracket. An integral digital LCD with integrated keypad is included on the front face, so commissioning, span re-range, and trim happen at the instrument without a handheld — useful on a crowded skid where bringing a 375 communicator out is the slow part of the loop check.

Documentation the buyer receives

The build ships with an EN 10204-3.1 inspection certificate covering a 9-point calibration, plus an EN 10204-2.2 test report on the pressure-bearing and process-wetted parts (gaskets excluded) — the paper pack a QA reviewer expects when a DP transmitter lands on a pressure-boundary BOM line.

Sourcing and lead-time posture

Lifecycle is recorded as current on the ABB 266DSH line, with an estimated 4–6 week lead time — the part is configured-to-order against the order-code string rather than pulled off a shelf, so quoting and confirmation run through an RFQ on this exact suffix.

MPN
266DSHHSMA1B1L1C1H4