Skip to main content
Schneider Electric MH30702P17F2200

Schneider Electric MH30702P17F2200 Servo Motor with Brake

MPN MH30702P17F2200
Active

Schneider Electric MH30702P17F2200 MH3 series servo motor with brake, 1380 W continuous power, 5500 rpm nominal speed, 2.37 N.m nominal torque, IP65, multiturn SinCos Hiperface encoder, 70 mm flange.

Dispatch SLA24-48h Global Rush
Quality CheckOriginal Seal & Physical QC
IncotermsDAP / DDP Available
Source DocumentedChannel stated on listing & quote
Condition PhotosReal unit photos / video on request
WhatsApp AnswersFast human replies for machine-down parts
Worldwide DispatchDHL/FedEx — transit quoted per order
Independent China distributor & stockist· Listing updated Sep 2026

Specifications

MH30702P17F2200 specifications
ParameterValue
Encoder typeMultiturn SinCos Hiperface
Shaft end typeParallel key
Main product or component typeServo motor
IP ratingIP65
Length7.6 in (193 mm)
Shaft diameter0.4 in (11 mm)
Max radial force fr n710 N 1000 rpm 560 N 2000 rpm 490 N 3000 rpm 450 N 4000 rpm 410 N 5000 rpm 390 N 6000 rpm
Centring collar diameter2.4 in (60 mm)

Product details

The MH30702P17F2200: The holding brake delivers 3 N.m static torque — enough to hold a vertical-axis load at standstill without the drive having to maintain a holding current. Brake pull-in power is only 7 W, so the thermal load on the motor end-bell stays modest even with frequent engage/release cycles. Torque output depends on which LXM5x or LXM6x drive supplies it: at 115 V three-phase you get the full 2.37 N.m; at 480 V three-phase it derates to 1.89 N.m. The peak stall torque is 7.4 N.m across the voltage range — useful for acceleration transients or breaking away a stuck load.

Encoder, feedback, and position-hold for safety circuits

The multiturn SinCos Hiperface encoder gives absolute position over multiple shaft revolutions — no homing sequence needed after a power cycle. This matters for applications where the axis must resume from the last known position after an E-stop or unplanned shutdown. IP65 rating on the motor body and the rotatable right-angled connectors means the assembly withstands washdown and airborne particulates. The connector rotates to orient the cable exit — useful when the motor mounts in a tight enclosure corner and the cable needs to route without a tight bend radius.

Mounting interface and mechanical limits

The 70 mm IEC flange (2.8 in) with a 0.2 in (5.5 mm) mounting hole pattern and 0.10 in (2.5 mm) centring collar depth matches standard metric servo mounting dimensions. Shaft is 11 mm diameter with a parallel key, 23 mm engagement length — fits standard couplings and pulleys. Maximum radial force on the shaft drops with speed: 710 N at 1000 rpm, 390 N at 6000 rpm. If this motor drives a belt or a direct-mounted pulley, the belt tension must stay below the speed-dependent limit or the front bearing life shortens.

Electrical parameters for drive matching

Stator resistance is 3.84 Ohm and inductance is 12.19 mH — the electrical time constant (L/R) is about 3.2 ms, which sets the current-loop bandwidth ceiling. The torque constant is 0.84 N.m/A at 120 °C copper temperature, and the back EMF constant is 54.08 V/krpm — both needed to calculate the drive's voltage and current requirements at top speed. Maximum continuous current is 9.65 A RMS; the 3-second peak current is also 9.65 A, so the drive's peak-current rating must match or exceed this for acceleration transients. Natural convection cooling means no external fan or air supply — the motor sheds heat through the flange and housing surface.

MPN
MH30702P17F2200