Skip to main content
Schneider Electric ILM1401M21F0000

Schneider Electric ILM1401M21F0000 PacDrive 3 Servo Motor

MPN ILM1401M21F0000
Obsolete

Schneider Electric PacDrive 3 ILM series integrated servo motor, ILM1401M21F0000, 8.3 N·m nominal torque, 27 N·m peak, 1300 W, 140 mm flange, IP65.

Dispatch SLA24-48h Global Rush
Quality CheckOriginal Seal & Physical QC
IncotermsDAP / DDP Available
Source DocumentedChannel stated on listing & quote
Condition PhotosReal unit photos / video on request
WhatsApp AnswersFast human replies for machine-down parts
Worldwide DispatchDHL/FedEx — transit quoted per order
Independent China distributor & stockist· Listing updated Sep 2026

Specifications

ILM1401M21F0000 specifications
ParameterValue
Shaft end typeUntapped
Main product or component typeServo motor integrated drive
IP ratingIP65
Length11.5 in (292 mm)
Shaft diameter0.9 in (24 mm)
Max axial force fa n0.2 x Fr
Max radial force fr n2210 N 1000 rpm 1760 N 2000 rpm
Centring collar diameter5.1 in (130 mm)

Product details

An all-in-one motor/drive with a 140 mm flange footprint

The Schneider Electric ILM1401M21F0000 is a PacDrive 3 series ILM servo motor with an integrated drive stage, built around an international standard flange with a 5.5 in (140 mm) motor flange size and a body length of 11.5 in (292 mm), so it drops into a standard NEMA-style machine mount without adapter plates. Natural convection cooling is the only thermal path on the unit, which keeps the cabinet clean of fans and ducting — but it also means the continuous torque rating assumes the mounting surface acts as a heatsink, and a stuffed enclosure will pull continuous torque down long before it trips the peak figure.

Torque, speed, and what the 1300 W envelope actually means on the line

Continuous stall torque lands at 8.5 N·m with a continuous stall current of 3.2 A and a line-rated current of 3.15 A, while peak stall torque reaches 27 N·m and the drive can deliver a maximum Irms of 14.6 A — that's roughly a 3× overload headroom for short accel/decel bursts on a conveyor index or a small press feed. Nominal torque is 8.3 N·m at the rated 1500 rpm, which lines up with the 1300 W nominal output power — pick a gearbox or pulley ratio off the 8.3 N·m figure for steady-state sizing, and reserve the 27 N·m peak only for short move profiles where duty cycle stays below the thermal ceiling.

Feedback, brake, and shaft detail for the panel-builder

Position feedback is an absolute single-turn SinCos Hiperface encoder, so the controller reads absolute shaft position on power-up with no homing routine — appropriate for indexed motion where losing position after an E-stop would cost a re-home cycle. A holding brake is fitted and rated 18 N·m holding torque, paired with a 24 mm untapped shaft and a 2.0 in (50 mm) shaft length with one keyway at 1.6 in (40 mm) width — there is no second shaft end, so any auxiliary encoder or hand-crank decoupler needs its own bracket. Maximum radial load is 2210 N at 1000 rpm, dropping to 1760 N at 2000 rpm, and maximum axial force is capped at 0.2 × Fr — a belt drive with too much pre-tension will eat the bearings long before the drive ever faults.

Sealing, electrical constants, and what IP65 actually buys you

IP65 sealing on the motor body suits washdown-adjacent areas and most outdoor enclosures, but it is not IP67 — high-pressure hot-water cleaning directly on the unit will eventually defeat the seal. Stator resistance reads 4.58 Ohm phase-to-phase at 20 °C and 3.18 Ohm phase-to-neutral at 120 °C, with stator inductance of 50 mH Ph/Ph at 20 °C and 25 mH Ph/N at 120 °C — these are the values to feed into a torque-loop or field-weakening model, and the temperature coefficient is significant enough that a cold-start tune will drift once the motor warms up.

MPN
ILM1401M21F0000