Skip to main content
Schneider Electric MH30703P06A2200

Schneider Electric MH30703P06A2200 Servo Motor, 1540 W

MPN MH30703P06A2200
Active

Schneider Electric MH30703P06A2200 servo motor, three phase, 1540 W continuous power, 5000 rpm nominal speed, IP65, single-turn SinCos Hiperface encoder, smooth shaft 14 mm diameter.

Dispatch SLA24-48h Global Rush
Quality CheckOriginal Seal & Physical QC
IncotermsDAP / DDP Available
Source DocumentedChannel stated on listing & quote
Condition PhotosReal unit photos / video on request
WhatsApp AnswersFast human replies for machine-down parts
Worldwide DispatchDHL/FedEx — transit quoted per order
Independent China distributor & stockist· Listing updated Sep 2026

Specifications

MH30703P06A2200 specifications
ParameterValue
Encoder typeSingle turn SinCos Hiperface
Shaft end typeSmooth shaft
Main product or component typeServo motor
IP ratingIP65
Length7.3 in (186 mm)
Shaft diameter0.6 in (14 mm)
Centring collar diameter2.4 in (60 mm)

Product details

Motor frame and mechanical fit

The MH30703P06A2200 carries a 70 mm flange (2.8 in) with a 60 mm centring collar and 2.5 mm centring depth — this matches the standard international flange pattern for servo motors in this power class, so the pilot diameter and bolt circle are the first check against the mating gearbox or machine frame. Shaft is smooth, 14 mm diameter by 30 mm long — no keyway, no second shaft end. The coupling must clamp on the smooth surface; verify the bore tolerance and set-screw torque against the shaft hardness to avoid slip under peak torque. Overall length is 186 mm (7.3 in) — this dimension plus the connector overhang determines the envelope in a tight axis layout. The rotatable right-angled connectors let the cable exit in any of four orientations, which helps when routing around adjacent motors or panel walls.

Torque and speed capability

Nominal torque depends on the drive voltage and phase configuration: 3.18 N·m at 115 V three-phase, 2.96 N·m at 230 V single-phase, 2.53 N·m at 400 V three-phase, and 2.26 N·m at 480 V three-phase. The continuous stall torque is 3.4 N·m across the 115–480 V three-phase range, with a peak stall torque of 10.2 N·m — about 3× the continuous rating, which handles short acceleration bursts without tripping the drive. Continuous power is 1540 W at 480 V — this is the thermal limit for continuous duty. The torque constant is 0.87 N·m/A at 120 °C copper temperature, and the back EMF constant is 55 V/krpm, which defines the voltage-speed curve for the drive's velocity loop tuning.

Electrical and environmental ratings

Stator resistance is 2.65 Ω and inductance is 8.64 mH — these values set the electrical time constant and the current-loop bandwidth limit for the servo drive. The maximum continuous RMS current is 3.91 A, with a 3-second peak of 12.57 A. IP65 protection means the motor body is dust-tight and protected against low-pressure water jets — suitable for washdown areas in food processing or machining coolant environments, but not for immersion or high-pressure spray. The connector seals are the critical point; verify the mating cordset also carries an IP65 rating. Maximum radial force on the shaft bearing is load-dependent: 730 N at 1000 rpm, dropping to 430 N at 5000 rpm, and 400 N at 6000 rpm. Belt-driven applications must respect this curve to avoid bearing overload.

Sourcing and lifecycle status

The encoder is a single-turn SinCos Hiperface type — this is a common feedback interface for Schneider's Lexium 52 and Lexium 62 drive families. The motor is sized for those drives, with nominal torque values listed for both LXM52 and LXM62 at multiple supply voltages. No pin-compatible alternative is recorded; the MH30703P06A2200 is the specific variant with smooth shaft, no brake, and single-turn encoder.

MPN
MH30703P06A2200