Skip to main content
Log in
Schneider Electric A9N2P32CIN — 2-Pole MCB (DIN Rail)

Schneider Electric A9N2P32CIN Acti9 xC60 MCB, 32 A, 2P, C-Cu

MPNA9N2P32CIN
Active

Schneider Electric Acti9 xC60, miniature circuit breaker, A9N2P32CIN, 32 A, 2P, C-curve, 10 kA at 380-415 V AC, clip-on 35 mm DIN rail.

Sourced new & surplus through independent channelsAuthenticity-screened · ESD-safe packingListing updated Jul 2026

Specifications

A9N2P32CIN — Identification
ParameterValue
Product nameXC60
Product rangeActi9
Series / familyActi9
Device short namexC60
Product / component typeMiniature circuit-breaker
Device applicationDistribution
A9N2P32CIN — Electrical
ParameterValue
Rated current [In]32 A
Number of protected poles2
Pole configuration2P
Rated operational voltage [Ue]220...240 V AC 50/60 Hz 380...415 V AC 50/60 Hz 100...125 V DC
Network type (AC/DC)DC AC
Network frequency50/60 Hz
A9N2P32CIN — Protection
ParameterValue
Tripping curve codeC
Magnetic tripping limit8 x In +/- 20 %
Breaking capacity (Icu)10 kA Inc at 380...415 V AC 50/60 Hz conforming to IS/IEC 60947-2 6 kA Icu at 100...125 V DC conforming to IS/IEC 60947-2
Rated service breaking capacity [Ics]6 kA conforming to IS/IEC 60947-2 - 100...125 V DC 7.5 kA conforming to IS/IEC 60947-2 - 380...415 V AC 50/60 Hz
Energy limitation class3 conforming to IS/IEC 60947-2
Suitable for isolationYes conforming to IS/IEC 60947-2
Overvoltage categoryIV
Trip unit technologyThermal-magnetic
Earth-leakage protectionSeparate block
Operating / control typeToggle
Mechanical durability (cycles)20000 cycles
A9N2P32CIN — Mechanical
ParameterValue
9 mm pitches4
Width36 mm
Height85 mm
Depth77.5 mm
Mounting support35 mm DIN rail
Mounting modeClip-on
Terminal connectionsBiconnect (bottom) Tunnel type terminals (bottom) 25 mm² flexible Tunnel type terminals (bottom) 35 mm² rigid
Terminal tightening torque3.5 N.m
Comb busbar / distribution block compatibilityTop: YES
Local signalling / indicationON/OFF indication
Contact position indicatorYes
A9N2P32CIN — Environmental
ParameterValue
Operating temperature range-30...70 °C
Storage temperature range-40...85 °C
Relative humidity95 % at 55 °C
A9N2P32CIN — Approvals
ParameterValue
Standards / complianceIS/IEC 60947-2

Product details

Breaking capacity & coordination

Rated at 10 kA Inc at 380-415 V AC (IS/IEC 60947-2), with a DC rating of 6 kA Icu at 100-125 V DC. That AC figure is typical for a 32 A MCB in a sub-distribution board backed by a larger upstream breaker — the 10 kA withstand covers the prospective fault current in most building-service panels. The DC rating is lower, so if this breaker is used in a DC circuit, the available fault current must not exceed 6 kA. The utilisation category is Category A (no intentional short-time delay), which is standard for MCBs — it trips fast on a short circuit, no selectivity with downstream devices unless they are current-limiting.

Mounting & connection

The 36 mm width (4 x 9 mm pitches) is the standard 2-module footprint for a 2-pole MCB — fits any DIN-rail enclosure. Wire strip length is 13 mm for top or bottom connection. IP20 finger-safe protection on the front face, suitable for enclosed panels only.

Environmental & isolation

Overvoltage category IV (equipment for the origin of the installation, e.g., main distribution boards). Suitability for isolation is confirmed to IS/IEC 60947-2 — the breaker provides a visible isolation gap when switched off.

Frequently asked questions

What are the key ratings of A9N2P32CIN?

Rated current 32 A, 2 poles, C-curve trip, breaking capacity 10 kA at 380-415 V AC and 6 kA at 100-125 V DC, thermal-magnetic trip unit, suitable for isolation per IS/IEC 60947-2.

What compliance documentation does A9N2P32CIN have?

The breaker is certified to IS/IEC 60947-2. The evidence does not list RoHS, REACH, or UL documentation specifically — these are typically covered by the manufacturer's general compliance declarations for the Acti9 range.

MPN
A9N2P32CIN