Skip to main content
Log in
Schneider Electric SH30702P1AA4000 — Servo Motors with Brake

Schneider Electric SH30702P1AA4000 Servo Motor, 1130 W

MPNSH30702P1AA4000
Active

Schneider Electric SH30702P1AA4000 SH3 servo motor, three-phase, 1130 W continuous power, 3000 rpm nominal speed, 2.1 Nm nominal torque, absolute single-turn Hiperface DSL encoder, IP65, 70 mm flange.

$1,215.00Ref. price · indicative, final on quote
Schneider Electric SH30702P1AA4000 datasheet (PDF)
Sourced new & surplus through independent channelsAuthenticity-screened · ESD-safe packingListing updated Aug 2026

Specifications

SH30702P1AA4000 — Identification
ParameterValue
Product typeServo motor
Holding brakeWithout
SH30702P1AA4000 — Performance
ParameterValue
Nominal torque18.6 lbf.in (2.1 N.m) 230 V single phase 15.9 lbf.in (1.8 N.m) 400 V three phase 15.9 lbf.in (1.8 N.m) 480 V three phase
Nominal output power610 W 230 V single phase 1130 W 400 V three phase 1130 W 480 V three phase
Continuous power1130 W
Nominal speed3000 rpm 230 V single phase 6000 rpm 400 V three phase 7200 rpm 480 V three phase
Maximum mechanical speed8000 rpm
Continuous stall torque18.06 lbf.in (2.04 N.m) 115...480 V three phase
Peak stall torque67.3 lbf.in (7.6 N.m) 115...480 V three phase
Rotor inertia0.410 kg.cm²
SH30702P1AA4000 — Electrical
ParameterValue
Rated supply voltage (Us)115...480 V
Network phases3
PhaseThree phase
Maximum current (Irms)11.8 A
Continuous stall current2.9 A
Torque constant0.7 N.m/A 248 °F (120 °C)
Back-EMF constant48 V/krpm 68 °F (20 °C)
Number of motor poles3.0
Stator resistance4.2 Ohm
Stator inductance10.65 mH
Electrical connectionStraight connector
SH30702P1AA4000 — Feedback
ParameterValue
Encoder typeAbsolute single turn Hiperface DSL
Speed feedback resolution262144 points/turn
SH30702P1AA4000 — Mechanical
ParameterValue
Shaft end styleParallel key
Shaft diameter0.4 in (11 mm)
Shaft length0.9 in (23 mm)
Key width0.2 in (4 mm)
Motor flange size2.8 in (70 mm)
Mounting supportInternational standard flange
Length7.4 in (187 mm)
Number of mounting holes4
Mounting-hole diameter0.2 in (5.5 mm)
Mounting-hole bolt circle diameter3.2 in (82 mm)
Centring collar diameter2.4 in (60 mm)
Centring collar depth0.10 in (2.5 mm)
Maximum radial force (Fr)900 N 1000 rpm
Maximum axial force (Fa)160 N
SH30702P1AA4000 — Environmental
ParameterValue
IP degree of protectionIP65 motor: conforming to IEC 60034-5 IP54 shaft bushing without shaft seal ring: conforming to IEC 60034-5
Cooling methodNatural convection
Winding (copper hot) temperature266 °F (130 °C)

Product details

Motor ratings across supply voltages

The SH30702P1AA4000 is a three-phase SH3 servo motor from Schneider Electric. Its performance depends on the supply: at 400 V three-phase it delivers 1130 W continuous power and 1.8 Nm nominal torque, while at 230 V single-phase the output drops to 610 W and 2.1 Nm. Nominal speed reaches 3000 rpm on 230 V single-phase, 6000 rpm on 400 V three-phase, and 7200 rpm on 480 V three-phase — the speed ceiling is set by the supply voltage and phase configuration. Peak stall torque is 7.6 Nm across the 115...480 V three-phase range, with continuous stall torque at 2.04 Nm. The torque constant is 0.7 Nm/A at 120 °C copper temperature.

Encoder and feedback interface

This motor carries an absolute single-turn encoder using the Hiperface DSL digital interface — a single-cable feedback protocol that carries both power and position data over the motor cable, reducing wiring complexity in the cabinet. Back EMF constant is 48 V/krpm at 20 °C, which sets the voltage-speed relationship for drive tuning and regeneration braking limits.

Mechanical fit and mounting

Flange size is 70 mm (2.8 in) with an international standard flange pattern — mounting holes are 5.5 mm diameter on a 60 mm centring collar. Shaft diameter is 11 mm with a parallel key, key width 4 mm, shaft length 23 mm. Overall length is 187 mm (7.4 in). The motor is cooled by natural convection — no external fan or forced air required, but the mounting surface must allow free airflow around the housing. Maximum radial force at the shaft is 900 N at 1000 rpm, and maximum axial force is 160 N — these limits govern the allowable belt tension or direct coupling load.

Environmental protection and connections

IP65 rated per IEC 60034-5 for the motor body, with IP54 at the shaft bushing when the shaft seal ring is omitted — suitable for washdown environments if the shaft seal is specified. Electrical connection is via a straight connector or a quicklock rotatable right-angled connector. Stator resistance is 4.2 Ohm and inductance is 10.65 mH — these values are used by the drive for current-loop tuning and thermal modelling. Maximum continuous current Irms is 11.8 A, with the same value for 3-second peak output.

Sourcing and lifecycle status

The sizing reference SH30702P anchors this motor in the SH3 family; confirm the mating drive and cable set compatibility before specifying.

Frequently asked questions

What is the nominal speed of SH30702P1AA4000 at different supply voltages?

Nominal speed is 3000 rpm on 230 V single-phase, 6000 rpm on 400 V three-phase, and 7200 rpm on 480 V three-phase. The speed range depends on the supply configuration.

What encoder type does SH30702P1AA4000 use?

It uses an absolute single-turn encoder with Hiperface DSL digital interface — a single-cable feedback protocol that combines power and data, simplifying the wiring run between drive and motor.

What is the IP rating of SH30702P1AA4000?

The motor body is IP65 per IEC 60034-5, with IP54 at the shaft bushing when the shaft seal ring is not fitted. The IP65 rating covers the housing against dust and low-pressure water jets.

MPN
SH30702P1AA4000