Skip to main content
Log in
Schneider Electric SH31003P02A2200 — Servo Motors with Brake

Schneider Electric SH31003P02A2200 Servo Motor, 2400 W

MPNSH31003P02A2200
Active

Schneider Electric SH3 series servo motor, SH31003P02A2200, 2400 W continuous power, 8 N.m continuous stall torque, three-phase, absolute multiturn SinCos Hiperface encoder, smooth shaft, IP65/IP67.

Schneider Electric SH31003P02A2200 datasheet (PDF)
Sourced new & surplus through independent channelsAuthenticity-screened · ESD-safe packingListing updated Aug 2026

Specifications

SH31003P02A2200 — Identification
ParameterValue
Product typeServo motor
Holding brakeWithout
SH31003P02A2200 — Performance
ParameterValue
Nominal torque45.1 lbf.in (5.1 N.m) 480 V three phase 66.4 lbf.in (7.5 N.m) 115 V single phase 62.0 lbf.in (7 N.m) 230 V single phase 50.4 lbf.in (5.7 N.m) 400 V three phase
Nominal output power790 W 115 V single phase 1470 W 230 V single phase 2390 W 400 V three phase 2560 W 480 V three phase
Continuous power2400 W
Nominal speed1000 rpm 115 V single phase 2000 rpm 230 V single phase 4000 rpm 400 V three phase 4800 rpm 480 V three phase
Maximum mechanical speed6000 rpm
Continuous stall torque70.8 lbf.in (8 N.m) 115...480 V three phase
Peak stall torque250.5 lbf.in (28.3 N.m) 115...480 V three phase
Rotor inertia3.22 kg.cm²
SH31003P02A2200 — Electrical
ParameterValue
Rated supply voltage (Us)115...480 V
Network phases3
PhaseThree phase
Maximum current (Irms)28.3 A
Continuous stall current6.6 A
Torque constant1.22 N.m/A 248 °F (120 °C)
Back-EMF constant77 V/krpm 68 °F (20 °C)
Number of motor poles4.0
Stator resistance1.43 Ohm
Stator inductance4.7 mH
Electrical connectionRotatable right angled connector
SH31003P02A2200 — Feedback
ParameterValue
Encoder typeAbsolute multiturn SinCos Hiperface
Speed feedback resolution128 periods
SH31003P02A2200 — Mechanical
ParameterValue
Shaft end styleSmooth shaft
Shaft diameter0.7 in (19 mm)
Shaft length1.6 in (40 mm)
Motor flange size3.9 in (100 mm)
Mounting supportInternational standard flange
Length9.5 in (240.5 mm)
Number of mounting holes4
Mounting-hole diameter0.4 in (9.0 mm)
Mounting-hole bolt circle diameter4.5 in (115 mm)
Centring collar diameter3.7 in (95 mm)
Centring collar depth0.1 in (3.5 mm)
Maximum radial force (Fr)1050 N 1000 rpm 830 N 2000 rpm 730 N 3000 rpm 660 N 4000 rpm
Maximum axial force (Fa)160 N
SH31003P02A2200 — Environmental
ParameterValue
IP degree of protectionIP65 motor: conforming to IEC 60034-5 IP65 shaft bushing: conforming to IEC 60034-5 IP67 housing: conforming to IEC 60034-5
Cooling methodNatural convection
Winding (copper hot) temperature266 °F (130 °C)

Product details

Power and torque across the supply range

The SH31003P02A2200: This SH3 frame delivers 2400 W continuous power, but the nominal torque and speed shift with the supply voltage — a single motor covers 115 V single-phase through 480 V three-phase installations. At 480 V three-phase you get 5.1 N.m at 4800 rpm; drop to 115 V single-phase and it's 7.5 N.m at 1000 rpm. The continuous stall torque holds at 8 N.m regardless of supply, so the holding torque at zero speed is consistent.

Encoder and feedback — what the drive needs to see

Absolute multiturn SinCos Hiperface encoder — that's a sine-cosine interface with Hiperface protocol, common on Schneider Lexium drives. The drive's feedback card must support Hiperface; a standard incremental encoder input won't read it. Back EMF constant is 77 V/krpm at 20 °C, and torque constant is 1.22 N.m/A at 120 °C hot copper. These two numbers set the drive's current loop gain and the bus voltage headroom needed to reach rated speed under load.

Mounting and environmental sealing

International standard flange, 100 mm square, with a 95 mm centring collar and 9 mm mounting holes. Smooth shaft, 19 mm diameter, 40 mm length — no keyway, so the coupling must clamp or use a set-screw hub. IP65 on the motor body and shaft bushing, IP67 on the housing — that's dust-tight and protected against hose-directed water. The rotatable right-angled connector lets you route the cable in tight enclosures without a right-angle adapter.

Sourcing and lifecycle — active, quoted to order

Sourced through independent distribution against an RFQ.

Frequently asked questions

What drive works with the SH31003P02A2200 encoder?

The absolute multiturn SinCos Hiperface encoder requires a drive with a Hiperface-compatible feedback interface. Schneider's Lexium 28 or Lexium 32 series with the appropriate encoder option card will read it; a generic incremental encoder input will not.

Can this motor run on single-phase power?

Yes — the nominal speed and torque tables include 115 V single-phase and 230 V single-phase entries. At 115 V single-phase it delivers 790 W output at 1000 rpm; at 230 V single-phase it delivers 1470 W at 2000 rpm.

MPN
SH31003P02A2200