Skip to main content
Schneider Electric ILM1001P01F0000

Schneider ILM1001P01F0000 Servo Motor, 600 W, PacDrive 3

MPN ILM1001P01F0000
Active

Schneider Electric ILM1001P01F0000 PacDrive 3 integrated-drive servo motor, 600 W at 3000 rpm, 100 mm flange, holding brake, Hiperface feedback, IP54.

Dispatch SLA24-48h Global Rush
Quality CheckOriginal Seal & Physical QC
IncotermsDAP / DDP Available
Source DocumentedChannel stated on listing & quote
Condition PhotosReal unit photos / video on request
WhatsApp AnswersFast human replies for machine-down parts
Worldwide DispatchDHL/FedEx — transit quoted per order
Independent China distributor & stockist· Listing updated Sep 2026

Specifications

ILM1001P01F0000 specifications
ParameterValue
Shaft end typeUntapped
Main product or component typeServo motor integrated drive
IP ratingIP54
Length9.6 in (243 mm)
Shaft diameter0.7 in (19 mm)
Max axial force fa n0.2 x Fr
Max radial force fr n900 N 1000 rpm 720 N 2000 rpm 630 N 3000 rpm
Centring collar diameter3.7 in (95 mm)

Product details

An integrated drive on the PacDrive 3 line — what changes

The Schneider Electric ILM1001P01F0000 ships as a single unit that pairs a brushless servo motor with its drive electronics on a 100 mm flange — the 'integrated drive' short name (ILM) signals there is no separate drive cabinet to wire back to the cabinet, which matters where a clean machine-build footprint is part of the BOM value rather than separated power and control boxes. Natural-convection cooling means no fan or cold plate is sized into the enclosure layout; the unit takes 600 W of continuous output at 3000 rpm nominal and peaks at 85.0 lbf.in (9.6 N.m) of stall torque against a 16.8 lbf.in (1.9 N.m) nominal torque figure.

Holding brake, feedback, and the load-side envelope

The 48.7 lbf.in (5.5 N.m) holding brake holds the axis at standstill with the controller power removed — for vertical axes or horizontal loads parked during an E-stop, the brake torque figure is the number that lets a panel builder check the load will hold before the next motion segment. A single-turn SinCos Hiperface feedback device is fitted to the shaft, which is what the PacDrive 3 controller indexes against on power-up. Peak radial load on the shaft is 900 N at 1000 rpm and drops to 630 N at 3000 rpm — the bearing envelope is rpm-dependent, so a belt or pinion that pulls 700 N at the pulley needs a load check at the worst-case operating rpm rather than against the headline number at zero speed. Maximum axial force Fa is capped at 0.2 × Fr, which keeps the bearing thrust under control for both directions of belt tensioning. The 8-pole rotor winding is built as a single stack (1 stack), fixing the torque-per-amp behaviour the controller tunes against.

Electrical ratings a sizing calculation depends on

Continuous stall torque is 22.1 lbf.in (2.5 N.m) at a continuous stall current of 1.8 A, while the peak current ceiling is 7.4 A Irms — the 1.39 N.m/A torque constant (248 °F / 120 °C junction) is the conversion factor the drive current loop uses to close the loop, and it differs slightly from a 25 °C lab reading. Back-EMF is 90 V/krpm at 20 °C — that figure is the no-load line-voltage the motor generates per 1000 rpm, used to set the drive's DC-bus-headroom limits under deceleration. Line-rated current is 1.4 A from a low-voltage DC bus typical of an integrated-drive architecture; stator resistance at 20 °C Ph/Ph is 9.8 Ohm (6.82 Ohm Ph/N at 120 °C) and stator inductance 45.7 mH Ph/Ph (22.85 mH Ph/N at 120 °C) — both figures drift with hot windings and matter for current-loop gain tuning.

Panel-side mounting and IP rating

The flange size is 100 mm and uses 4 mounting holes at 9 mm diameter with a centring collar 95 mm × 3.5 mm deep — a standard IEC-style flange the cabinet designer lays out once for the entire ILM family, with the tapped shaft-left / untapped shaft-right variant selected by the order code suffix. IP54 with natural convection means the unit suits general industrial enclosures but not washdown or outdoor exposure — a gasket at the flange face is the wet-end barrier and the spline/key length (30 mm key across a 1.6 in / 40 mm shaft end) is sized to standard parallel keys.

Where this sits in the build and how it is sourced

There is no second-source or pin-compatible family member on the record; the 100 mm frame, 8-pole single-stack winding, and PacDrive 3 controller membership are coupled rather than interchangeable.

MPN
ILM1001P01F0000