Skip to main content
Schneider Electric MH30701P12A2200

Schneider Electric MH30701P12A2200 Servo Motor, 930 W

MPN MH30701P12A2200
Active

Schneider Electric MH30701P12A2200 MH3 series servo motor, 930 W continuous power, 1.38 Nm nominal torque, 1250 rpm nominal speed, IP65, Multiturn SinCos Hiperface encoder, three-phase.

Dispatch SLA24-48h Global Rush
Quality CheckOriginal Seal & Physical QC
IncotermsDAP / DDP Available
Source DocumentedChannel stated on listing & quote
Condition PhotosReal unit photos / video on request
WhatsApp AnswersFast human replies for machine-down parts
Worldwide DispatchDHL/FedEx — transit quoted per order
Independent China distributor & stockist· Listing updated Sep 2026

Specifications

MH30701P12A2200 specifications
ParameterValue
Encoder typeMultiturn SinCos Hiperface
Shaft end typeParallel key
Main product or component typeServo motor
IP ratingIP65
Length4.8 in (122 mm)
Shaft diameter0.4 in (11 mm)
Max radial force fr n660 N 1000 rpm 520 N 2000 rpm 460 N 3000 rpm 410 N 4000 rpm 380 N 5000 rpm 360 N 6000 rpm
Centring collar diameter2.4 in (60 mm)

Product details

Motor fit for a motion axis

The MH30701P12A2200 is a three-phase servo motor from the Schneider Electric MH3 family, delivering 930 W continuous power with a nominal torque of 1.38 Nm at 1250 rpm when paired with an LXM52 or LXM62 drive on a 115 V single-phase supply. The Multiturn SinCos Hiperface encoder provides absolute position feedback over multiple shaft revolutions — no homing cycle is needed after a power cycle, which saves time on multi-axis machines that index to a known position on startup. IP65 rating means the motor body and connector interface are sealed against washdown — suitable for food processing, beverage filling, or any line where hoses are used for cleaning.

Torque and speed across drive voltages

Nominal torque varies with the drive and supply voltage: 1.38 Nm on 115 V single-phase, 1.34 Nm on 230 V single-phase, 1.30 Nm on 400 V three-phase, and 1.27 Nm on 480 V three-phase — the torque drop at higher voltages is small but should be factored into the load margin calculation. Nominal speed also shifts with the drive configuration: 1250 rpm on 115 V single-phase, 3000 rpm on 230 V single-phase, 5500 rpm on 400 V three-phase, and 7000 rpm on 480 V three-phase — the maximum mechanical speed is 8000 rpm, so the 7000 rpm operating point leaves headroom for overshoot during deceleration. Peak stall torque is 4.2 Nm across the 115–480 V three-phase range — this is the short-term overload available for acceleration, about 3× the nominal torque, which is typical for servo-class motors.

Electrical parameters for drive tuning

The torque constant is 0.79 Nm/A at 120°C copper temperature — this is the factor that converts the drive's current command into shaft torque, and it's specified at the hot operating point, not at room temperature, so the tuning stays valid under load. Stator resistance is 8.28 Ohm and inductance is 23.4 mH, giving an electrical time constant of about 2.8 ms — the current loop in the drive needs to be tuned with this time constant in mind to avoid overshoot or oscillation. Back EMF constant is 50.72 V/krpm — at 7000 rpm the motor generates about 355 V back EMF, which must stay below the drive's DC bus voltage to maintain current control authority. Continuous stall current is 1.78 A, and the maximum current is 5.97 A — the drive's peak current rating should be at least 6 A to deliver the full peak torque.

Mechanical integration and cooling

The motor uses natural convection cooling — no fan is fitted, so it relies on airflow from the machine motion or ambient circulation. In a confined cabinet or at low duty cycles, the continuous power may need derating. Maximum radial force at the shaft is 660 N at 1000 rpm, dropping to 360 N at 6000 rpm — this is the bearing load limit for belt drives or direct-coupled loads; exceeding it shortens bearing life. The rotatable right-angled connectors allow the cable exit to be oriented in four directions — useful when the motor is mounted in a tight space where a straight connector would hit a panel wall.

MPN
MH30701P12A2200