Skip to main content
Schneider Electric GC2511F5

Schneider Electric GC2511F5 TeSys GC Modular Contactor, 2P,

MPN GC2511F5
Active

Schneider Electric TeSys GC GC2511F5 modular contactor, 2-pole, 110 V AC 50 Hz control, AC-7A/AC-7B utilisation, DIN rail mount, 17.5 mm width.

Dispatch SLA24-48h Global Rush
Quality CheckOriginal Seal & Physical QC
IncotermsDAP / DDP Available
Source DocumentedChannel stated on listing & quote
Condition PhotosReal unit photos / video on request
WhatsApp AnswersFast human replies for machine-down parts
Worldwide DispatchDHL/FedEx — transit quoted per order
Independent China distributor & stockist· Listing updated Sep 2026

Specifications

GC2511F5 key specifications
ParameterValue
Control typeRemote control
Control circuit typeAC at 50 Hz
Main product or component typeModular contactor
Voltage<= 250 V AC
Coil voltage110 V AC 50 Hz
Insulation voltage ui500 V conforming to IEC 61095 500 V conforming to VDE 0110
Current25 A AC-7 A 8.5 A AC-7B
Utilization categoryAC-7B AC-7 A
Temp storage max70 °C
Temp storage min-40 °C
Temp operating max50 °C
Temp operating min-5 °C

All specifications

GC2511F5 additional specifications
ParameterValue
Storage temperature-40...70 °C
ColorWhite
Depth62.5 mm
Width17.5 mm
Height81 mm
Electrical life cyclesAC-7 A: 100000 cycles AC-7B: 100000 cycles
Mechanical life cycles1000000 cycles
ApplicationLighting Motor control Heating
Operating time10...25 ms opening 10...30 ms closing
Operating position30°/vertical
Operating temperature-5...50 °C

Product details

The GC2511F5 is a 2-pole modular contactor from the TeSys GC range, designed for switching lighting, motor, and heating loads. It uses a 110 V AC 50 Hz control circuit and carries AC-7A and AC-7B utilisation categories — so it's rated for resistive loads like heating elements (AC-7A) and moderate inductive loads like small motors (AC-7B). Let me show you why that matters for your panel: AC-7B specifically covers the higher inrush of motor starts, meaning this contactor can handle the locked-rotor current of fractional-horsepower motors without welding its contacts. The depth is 62.5 mm and height 81 mm — compact enough for shallow gland plates. Control and power connections are screw clamp terminals; torque both to 0.8 N·m. For the power circuit, it accepts up to 6 mm² flexible wire, which is plenty for the 25 A continuous rating.

For normal switching, the associated fuse rating is 25 A gL at ≤ 440 V for the power circuit, so size your upstream fuse accordingly. Electrical durability is 100,000 cycles for both AC-7A and AC-7B duty. Mechanical durability is 1,000,000 cycles. That means the contacts will last through 100,000 load-switching operations before you need to think about replacement — good for a machine that cycles a few times per minute over a few years. Maximum operating rate is 300 cycles per hour at 50 °C, so don't push it faster than one cycle every 12 seconds in continuous use. Heat dissipation is 1.3 W at 50/60 Hz, with 1.6 W per pole. That's low enough that you don't need to worry about thermal buildup in a standard IP40 enclosure, but if you're packing a dozen of these side by side, account for the total heat in your panel cooling calculation.

Where to use it — and where not to

This contactor is intended for lighting control, motor control (small motors), and heating applications. The AC-7A category covers resistive loads like incandescent lamps or electric heaters. AC-7B covers inductive loads like small single-phase motors, pumps, and fans — the kind you'd find in HVAC or light industrial equipment. It's not rated for heavy three-phase motor starting (that's AC-3 territory), so don't spec it for a 5 HP compressor. The control circuit is 110 V AC 50 Hz only. The coil operates between 0.85 and 1.1 times Uc and drops out between 0.2 and 0.75 Uc. Operating altitude is up to 3000 m. IP20 protection (fingers) on the contactor itself, IP40 when installed in an enclosure per VDE 0106. That means it's not suitable for washdown or dusty environments without a proper cabinet. The protective treatment is 'TC' — standard tropicalisation for humidity resistance, but not a sealed coating.

It's part of the broader TeSys GC family, which shares the same footprint and terminal layout across similar ratings. If you're standardising on a single contactor for multiple load sizes, the GC25 frame (this one) is the 25 A variant — there are smaller and larger versions in the same 17.5 mm-wide package. No direct pin-compatible replacement exists within the family because the GC25 is the current design; a future successor would be announced via a product change notice (PCN).

MPN
GC2511F5