Skip to main content
Schneider Electric ILM1002P11F0000

Schneider Electric ILM1002P11F0000 ILM Servo Motor, 910 W

MPN ILM1002P11F0000
Active

Schneider Electric PacDrive 3 ILM-series servo motor integrated drive, 910 W nominal, 100 mm flange, Hiperface single-turn SinCos feedback, keyed shaft with holding brake, IP54.

Dispatch SLA24-48h Global Rush
Quality CheckOriginal Seal & Physical QC
IncotermsDAP / DDP Available
Source DocumentedChannel stated on listing & quote
Condition PhotosReal unit photos / video on request
WhatsApp AnswersFast human replies for machine-down parts
Worldwide DispatchDHL/FedEx — transit quoted per order
Independent China distributor & stockist· Listing updated Sep 2026

Specifications

ILM1002P11F0000 specifications
ParameterValue
Shaft end typeKeyed
Main product or component typeServo motor integrated drive
IP ratingIP54
Length11.02 in (280 mm)
Shaft diameter0.7 in (19 mm)
Max axial force fa n0.2 x Fr
Max radial force fr n990 N 1000 rpm 790 N 2000 rpm 690 N 3000 rpm
Centring collar diameter3.7 in (95 mm)

Product details

What the part is — and why PacDrive 3 is the lead

The ILM1002P11F0000 is the short name ILM on a PacDrive 3 range servo motor integrated drive from Schneider Electric; the lifecycle stage reads current on the record, which is the only signal procurement gets on paper before an RFQ is opened. An integrated drive — motor plus drive electronics on a single shaft — removes the separate amplifier cabinet and the long motor cable that drags a radiated-emissions signature through the panel; the ILM line carries its own back-EMF and torque constants so the controller parameter set can be loaded without a separate motor ID step.

Headline ratings — power, torque, speed

Nominal output is 910 W at 3000 rpm with a continuous stall torque of 4.4 N·m and a peak stall torque of 18.3 N·m — the roughly 4:1 peak-over-continuous headroom is the envelope inside which a PacDrive 3 motion profile can accelerate a packaging-line, pick-and-place, or short-stroke feed axis without saturating the current loop. Maximum current Irms is 13.1 A against a line-rated current of 2 A and a continuous stall current of 2.9 A — the Irms ceiling is the peak the drive will source for acceleration bursts while the continuous figures govern steady-state thermal sizing.

Feedback, brake, and the electrical constants the controller needs

Position feedback is absolute single-turn SinCos Hiperface — single-turn means absolute position within one revolution without battery backup, which suits rotary axes that do not need to retain absolute position across power cycles; Hiperface is the protocol the PacDrive 3 drive expects on commissioning. The holding brake provides 5.5 N·m of holding torque — sized to hold the vertical axis in place with the motor de-energised, which is the fail-safe state machine builders usually design to on packaging and small-format handling axes. Stator resistance and inductance are given at both 20 °C and 120 °C; the temperature split lets the PacDrive commissioning tool place the current-loop gains with the cold figure first and the warm figure for thermal compensation — without both values the gain scheduler can drift a few percent across a warm-up shift.

Mechanical fit into the machine

International standard flange mounting on a 100 mm motor flange, keyed shaft at 19 mm diameter and 40 mm shaft length, with four 9 mm mounting holes and a 95 mm centring collar 3.5 mm deep — that geometry mates to the standard NEMA-derived footprint common on small-format packaging, labelling, and pick-and-place gearboxes, so a replacement on an existing axis drop-in is the usual path. Overall length is 280 mm with a 30 mm key width on the keyed shaft; the second-shaft end is not provided — relevant where a manual handwheel or auxiliary encoder is on the BOM, since this build does not accept it without a flange change. IP54 seals against dust and splashing water from any direction, so the motor is acceptable inside a machine cabinet and on a washdown-adjacent axis but not on a direct spray zone; natural convection cooling means no fan cut-out to wire and no dust draw-in through a fan grille. Maximum radial force drops from 990 N at 1000 rpm to 690 N at 3000 rpm and maximum axial force is limited to 0.2 × Fr — the radial curve is the one that decides whether the pulley or pinion can sit outboard or has to be moved inboard to stay under the load line on a high-speed axis.

Sourcing posture for the BOM line

Lifecycle stage reads current on the record — no second-source or official successor is cited on the file, so the part is sourced per RFQ through independent distribution channels and quoted against the BOM quantity rather than held on a shelf promise.

MPN
ILM1002P11F0000